top of page

Corten Care Range

Our range of Corten Care products are perfect if you like the way that rusted metal looks on your sculpture or architectural feature but hate the way that rust stains. Or, you are looking to create a patina and accelerate the natural corrosion of Corten steel?

​

The use of rusted metal, including weathered steel and Corten, is a rising trend in architecture and art. The colour and texture that is created when steel is rusted is beautiful. Unfortunately, rusted metals come with unique challenges. Often the rust comes off and stains clothing, water running over the surface casues brown run-off thaty stains anything is crosses, and this results is ruined clothing and irreparable damage to the surrounding areas. This is where our range of products come in to not only help create the desired finish, but also seal it to keep it looking that way, and protect it from damage, run-off, and staining.

​

We are proud to have added our water-based version of our coating to the range!

​

CT-7571-T and CT-7571-W Coatings will seal the rusted metal, stop the rusting process and will protect the metal from further corrosion.

Rusted metal is porous so care must be taken to ensure that the metal is completely clean and dry. Blooming rust should be knocked down and a solvent used to help remove contaminants like grease or oils, and also will help draw out moisture.
Coating and sealing moisture in the pores of metal can cause failure of any coating.

​

Seal in the
beauty of
Corten & Rusted Steel

​

There are 4 products in our Corten and Rusted metals range:

​

NEW CT-7571-W and CT-7571-T:

Our coatings provides the following benefits to rusted metal with every application:

  • Eliminate staining of surrounding areas from unsightly runoff and stains. Rusty drips on other substrates can ruin the look of a building.

  • Eliminate transfer of rust to people (hands & clothing).

  • Extend the life of the steel by protecting from further corrosion.

  • Give the surface a more finished, purposeful look.

  • Excellent adhesion on naturally or artificially rusted surfaces.

  • Self annealing and will blend to itself to create complete protection.

  • CT-7571-W is available in a Gloss and Satin finish.
     

We recommend CT-7571-W for most applications, especially internal areas.  The coating is white when applied, but dries in approximately 4 hours to seal in the surface.  A second thin coat is usually advised after the first coat to ensure the surface is fully sealed.

​

CT-7571-T is perfect for use in more extreme and exposed areas such as external application near to the coast.  When applying CT-7571-T it is vital that the surface is completely dry.  Usually 2 coats of CT-7571-T is enough, however we often recommend a third coat when being used in harsher environments.

​

Prep 505:

Prior to coating, surfaces need to neutralised to ensure nothing contaminates the coating.  For this, we recommend Prep 505, our biodegradable cleaning and neutralising product. Simply dilute 1 part to 4 parts and spray over the surface.  Leave for 2-3 minutes, and rinse with fresh water.
This process is even more vital is an accelerant has been used to weather the steel.

​

XL-08

If you are looking to actively weather your project, then we have developed an accelerator agent called XL-08.

XL-08 can be applied to bare Corten steel, or any metal you intend to rust, using a brush to ensure the solution gets in to the surface of the metal.  Once applied, ensure you monitor the effects of the accelerator until you reach the desired effect.  you may wish to add water to ensure the surface does not dry up.  You can also add more XL-08 if needed.
Once the surface has been weathered to the desired effect, rinse off the XL-08 with fresh, clean water and allow the metal to air dry.  If you are short on time, then you can flash dry the surface with isopropyl alcohol.
Before applying our coatings, ensure the surface has been neutralised.  We recommend using our Prep 505 cleaning and preparation fluid for this.

​

CT-7571-W Coating only - SATIN

CT-7571-W Coating only - GLOSS

CT-7571-W Kits - SATIN

CT-7571-W Kits - GLOSS

CT-7571-T Coating only

CT-7571-T kits

XL-08 and Prep 505

​

FAQs

​

How many coats do I need to apply? 
Rusted metal is very porous. The amount of CT-7571-T necessary to encapsulate the rust will depend on the depth of the rust. Using a Prep Pad or other slightly abrasive pad can remove blooming or thick rust will help to smooth out the metal but will still look rusted.

 

How do I clean and prep the metal for the coating?
Our coatings are easy to apply. Clean the surface to remove any lose particles and ensure no contaminants are on the surface. Next apply the coating. It is best NOT to use any water while cleaning. If necessary, use solvent to clean the surface. The rusted metal MUST be completely clean and DRY. The coating can be dabbed on with the lint free cloths provided, painted on with a brush, sprayed on or rolled on with a high density roller used for gloss paint. One to two coats are recommended on rusted metal because the metal is very porous and will absorb the coating.

 

What makes our coatings stand out from alternative options? 
CT-7571-T and CT-7571-W were developed by Bromoco International specifically for Corten steel and its increased use in architectural designs, sculptures, and home garden installations.
We had customers asking for a solutions to not only speed up the natural weathering of the steel, but also allow designers to create a patina that no longer corrodes or leaches and, as such, allows for colourful and creative installations.

bottom of page