This post is from a suggested group
Where is my 505
Just had my delivery but 505 prep fluid is missing from the large CT-7571-T kit, also the sealer doesn’t state that it’s SATIN anywhere on the label
5 Views
top of page
Share Us
Follow Us
0800 107 3243
Shipping Monday, Wednesday and Friday
Restore, protect, and keep it looking its best
Groups Feed
View groups and posts below.
This post is from a suggested group
Corten with new resin path instillation
Want to clean, accelerate and Matt seal before resin path installed, any experience in the group
16 Views
This post is from a suggested group
Everbrite satin finish ( large)
can i travel on a comercial flight to the Canary islands with this product in my suitcase. i must of sent 4 emails to everbrite asking this question and had no replies. thank you
61 Views
Song
22. Sept.
•
Thank you for your enquiry. If the product container is under 100ml, it may be carried in your hand luggage. If larger, it might be placed in your checked baggage. Baggage rules differ by airline, kindly confirm the exact requirements with your chosen airline :)
This post is from a suggested group
Stainless heat treated
Hi,
I have been heat treating some stainless steel, with great results. I would like to lacquer the piece to protect the vibrant colours but when I use ProtectaClear it seems to dull down the colours, especially the blues and purples. Can you recommend another finish?
Thanks,
Sam
132 Views
Song
05. Aug.
•
Hi Sam,
This effect shouldn’t occur with ProtectaClear. It dries to create a fully crystal clear protective coating. Often dulling can be caused by surface contaminants, uneven application, or residual greases on the heat-tinted stainless steel prior to coating.
Our suggestion is to remove the current layer, deep clean the stainless steel surface, and reapply ProtectaClear.
Hope it helps :)
This post is from a suggested group
Small Mirror Finish Copper & Brass Kit Covers 2.5㎡
Would this product work well on brass door push plates in order to stop having to polish them with brasso polish each week?
141 Views
Song
17. Juli
•
Hiya! Absolutely this kit is perfect for your brass door push plates — it’ll bid weekly Brasso polishing farewell for good!
Once you apply the coating, it locks in that polished shine long-term and forms a tough protective barrier to stop your brass from tarnishing and rusting.
If the brass has built up heavy tarnish already, we’d recommend prepping the surface first with our HD Deep Clean Gel for a thorough deep clean. This gets the metal into prime condition, letting the coating adhere flawlessly and deliver the best lasting finish.
This post is from a suggested group
Protect-a-clear
I would just like to say that this product is absolutely amazing. It is so easy to apply and the results are spot on. I use it on items that we gold plate. I recommend not using any Acetone to clean items as this causes issues that I quickly worked out. I tend to use smaller pieces of the lint free cloths also purchased and if lacquering larger items I use a few small pieces and have outstanding results. I just use the prep 1-4 mix and let dry and then straight on with the lacquer. I've never needed to use anything else at all to prep anything. This is on newly plated items that are not touched other than with nitrile gloves on.
210 Views
Song
01. Mai
•
Hi Lee, thank you very much for sharing; it’s been a great encouragement to us! Looking forward to these parts performing well!
This post is from a suggested group
Hello!
I am using Protectaclear on mild steel and copper parts. The first time I used it I good a good result. Since then the finish has not come out right. Please see attached pictures below , these taken after about 18 hours drying.
I have attempted to coat these particular parts twice now, and both times I have had a similar result. I had to spend nearly a day removing the finish with Acetone after the first failed attempt and now on the second attempt I have the same poor result! All parts are cleaned carefully with acetone and allowed to fully dry before coating. Indoor environment at around 15C, and I am using brand new lint free cloths each time. Application by wiping on and pot well shaken before use. It goes on fine initially and looks to be self levelling OK as expected, but then seems t…
254 Views
alexh1901
27. Apr.
Hi Song,
Much better this time, no problems and happy with the finish! Thank you!
Can I ask what you recommend for cleaning the finished surface?
Thanks!
Alex
This post is from a suggested group
Can protecaclear used on 304 stainless steel to prevent corrosion in coastal areas ,ie a harbour,if so would it need re treating
262 Views
Song
07. Apr.
•
Hi There! ProtectaClear is perfectly suited to your situation, but we would recommend PC279 instead. This product is designed to withstand environmental and chemical corrosion in coastal areas. We recommend neutralising and preparing the stainless steel surface with Cr24 Stainless Steel Deep Cleaner before applying ProtectaClear or PC279. If your stainless steel surface has developed rust, you can use ERW-XL rust remover to remove it. For routine maintenance, please avoid abrasive pads or harsh chemicals to maintain the finish and coating integrity. Hope this helps :)
This post is from a suggested group
Advice please
Hello!
I am looking to protect and seal mild steel with a brushed finish. Should I use ProtectaClear or the Stainless Steel protector fluid (PC 279)?
Which is the best cleaner to use?
Thanks!
Alex
248 Views
bottom of page
Hi there! We recommend our Corten / Ferous Metal Rust & Seal kit, which contains cleaner, accelerator and matt protective seal coating ready for use prior to resin path installation. For larger projects where the kit is insufficient, please contact our Commercial team. Our full YouTube playlist has step-by-step application guides.